series am ec40 - maz 40 w att | ac - dc / dc- dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r7. m 1 of 4 north america only features: models single output model input voltage (vac/hz) input voltage (vdc ) output voltage (v) output current max (a) efficiency (%) amec40 - 3.3smaz 90 - 264/ 47 - 440 120 - 370 3.3 8 78 amec40 - 5smaz 90 - 264/ 47 - 440 120 - 370 5 8 82 amec40 - 12sm az 90 - 264/ 47 - 440 120 - 370 12 3.33 84 amec40 - 15smaz 90 - 264/ 47 - 440 120 - 370 15 2.66 83 amec40 - 24smaz 90 - 264/ 47 - 440 120 - 370 24 1.6 6 82 models dual output model input voltage ( vac/hz) input voltage (vdc) output voltage (v) output current max (a) efficiency ( %) amec40 - 5dmaz 90 - 264/47 - 440 120 - 370 5 4 80 amec40 - 12dmaz 90 - 264/47 - 440 120 - 370 12 1.6 6 85 amec40 - 15dmaz 90 - 264/47 - 440 120 - 370 15 1.3 3 82 amec40 - 24dmaz 90 - 26 4 /47 - 440 120 - 370 24 0.835 77 note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. i nput specifications parameters conditions typical maximum units current 115 vac 1000 ma 230 vac 530 inrush current <2ms 115 vac 25 a 230 vac 50 leakage current 150 a external fuse recommended slow blow type 3.15 a input dissipation no load; 115vac no load; 264vac <0.5 <0.8 w start - up time 117 ms output specifications parameters conditions typical maximum unit s voltage accuracy 2 % line regulation (ll - hl) 0.5 % load regulation 0 - 100% load single 1 % 0 - 100% load dual 2 cross regulation 25% load - 1 st out, 100% load ? 2 nd out 5 % maximum capacitive load depending of the model 470 - 23 000 f t ransient response deviation 25% load step 2 % of vout ripple & noise * 20mhz bandwidth 50 mv p - p hold - up time (min) 115vac 29 ms minimum load current 0 % of max * ripple & noise measured with 0.1f m/c and 1f e/c ? connectors on input/output ? energy star compliant ? operating temperature: - 40c to +85c ? 4000vac i/o isolation ? over load, over voltage, short circuit protection ? low ripple and noise ? universal i nput: 90 - 264 vac, 47 - 440hz, or 120 - 370vdc ? ce, cu l us, cb approvals cb
series am ec40 - maz 40 w att | ac - dc / dc- dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r7. m 2 of 4 north america only isolation specifications parameters conditions typical rated units tested i/o voltage 3 sec 4000 vac isolation resistance >1000 m general specifications parameters conditions typical maximum units switching frequency 47 khz over current protection auto recovery 110 140 % over voltage protection zener diode clamp 110 % short circuit protection hiccup mode, indefinite short circuit restart auto recovery operating temperature with derating ab ove 5 0 oc - 40 - +85 o c maximum case temperature 100 o c storage temperature - 40 to +100 o c temperature coefficient 0.02 % / o c cooling free air convection humidity non condensing 95 % rh case material metal weight 27 0 g dimensions (l x h x w) 4.92 x 2.56 x 1.38 inches / 125 .00 x 65 .00 x 35 .00 mm mtbf > 800 000 hrs (mil - hdbk - 217f, t=+25 o c) environment approval test parameters conditions shock wave form half sine wave acceleration amplitude 5gn bump duration 30 ms converter operation before and after test, body mounted (on chassis) number of bumps 18 (3 in each direction for every axis) vibration test mode sweep sine, 10 - 100hz, speed 0.05hz/s displacement 1 mm acceleration 3g, 3 loops 30min one cycle, 3h total, every axis tested converter operation before and after test, body mounted (on chassis) safety specifications parameters agency approvals culus, ce , cb scheme standards medical electrical equipment iec \ en \ ul 60601 - 1 , csa - c22.2 no. 601.1 - m90 information t echnology equipment en 60950 - 1:2006+a11:2009 emi - conducted and radiated emission en550 11 , class b harmonic current emissions iec/en 61000 - 3 - 2, (en60555 - 2) voltage fluctuations and flicker iec/en 61000 - 3 - 3, (en60555 - 3) electrostatic discharge immu nity iec 61000 - 4 - 2 rf, electromagnetic field immunity iec 61000 - 4 - 3 electrical fast transient/burst immunity iec 61000 - 4 - 4 surge immunity iec 61000 - 4 - 5 rf, conducted disturbance immunity iec 61000 - 4 - 6 power frequency magnetic field immunity iec 6 1000 - 4 - 8 voltage dips, short interruptions immunity iec 61000 - 4 - 11
series am ec40 - maz 40 w att | ac - dc / dc- dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r7. m 3 of 4 north america only pin out specifications pin single dual 1 ac input (l) ac input (l) 2 ac input (n) ac input (n) 3 +v output +v output 4 - v output common 5 n.c. common 6 n.c. - v output n.c.: not connected dimensions ac input connector dc output connector 1 2 68 .63 (2.700) top view bottom view 3 4 5 6 2 .56 (65.00) 2 .56 (65.00) 4 .90 (125.00) 1 .28 (32.50) 0 .81 (20.50 ) 0 .88 (22.25 ) 2 .10 (53.25) dimensions: inch (mm) case tolerance: 0.05 (1.30 ) mounting holes (including din rail bracket) (m3) pcb bracket mounting screw pcb mounting screw pcb mounting screw customer chassis pcb mylar film mm max 2 . 6 35 . 00 ( 1 . 38 ) side view mylar film
series am ec40 - maz 40 w att | ac - dc / dc- dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r7. m 4 of 4 north america only optional din rail bracket derating - 40 - 20 0 20 40 60 80 100 100 80 60 40 20 0 safe operating area output power (%) 85 ambient temperature o c free air convection 50 o c note: 1. datasheets are updated as needed and as such, specifications are subject to change without notice. once printed or downloaded, datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. ai mtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary and may not be available for releas e. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control s ystems or other such applications which necessitate specific safety and regulatory standards other the ones listed in t his datasheet. 7. warranty is in accordance with aimtec?s standard terms of sale available at www.aimtec.com.
|
